How To Remove Skateboard Bearings

Table of Contents

Skateboarding is a popular and exciting sport that requires a lot of skill and practice. However, one of the most important aspects of maintaining your skateboard is keeping the bearings in good working condition. Bearings are small metal balls that allow the wheels to spin smoothly and efficiently. Over time, these bearings can become dirty, worn out, or damaged, which can affect the performance of your skateboard. 

 

In this article, we will discuss the steps you can take to remove the bearings from your skateboard and keep them in top condition. Whether you are a professional skater or a beginner, this guide will help you keep your skateboard running smoothly.

 

Tools And Materials Needed

  • Skate tool or bearing puller: This tool is specifically designed to remove and install skateboard bearings. It typically includes a bearing press and a bearing puller.
  • Flathead screwdriver: A flathead screwdriver can be used to remove any screws or bolts that may be holding the bearing in place.
  • Needle nose pliers: Needle nose pliers can be used to remove any debris or dirt that may be stuck in the bearing.
  • Cleaning solution: A cleaning solution, such as rubbing alcohol or degreaser, can be used to clean the bearings and remove any dirt or grime.
  • Lubricant: A lubricant, such as bearing oil or grease, can be used to lubricate the bearings after cleaning.
  • Replacement bearings: If the bearings need to be replaced, new bearings will be needed.
  • Protective gloves: Wearing protective gloves can help protect your hands from any debris or dirt that may be present on the bearings.
  • Clean rag: A clean rag can be used to wipe down the bearings and remove any remaining dirt or debris.

 

Step-By-Step Instruction

  1. Gather the necessary tools: You will need a bearing press or bearing puller, a skate tool (or a flathead screwdriver and a mallet), and a cleaning solution.
  2. Remove the wheels: Use the skate tool or flathead screwdriver to loosen the axle nuts and remove the wheels from the skateboard.
  3. Remove the bearings from the wheels: Place the wheel on a flat surface and use the bearing press or puller to remove the bearings from the wheel. If you do not have a bearing press or puller, you can also use a mallet and flathead screwdriver to gently tap out the bearings.
  4. Clean the bearings: Once the bearings are removed, clean them with a cleaning solution (such as rubbing alcohol or soap and water) and dry them thoroughly.
  5. Reassemble the wheels: Reinstall the cleaned and dried bearings back into the wheel and reattach the wheel to the skateboard. Tighten the axle nuts securely.
  6. Repeat the process for the other wheel.
  7. Finally, make sure to lubricate the bearings with a high-quality bearing lubricant before using your skateboard again. This will help keep them running smoothly and extend their lifespan.

 

Tips And Precautions

  • Use the right tools: To remove skateboard bearings, you will need a bearing remover tool or a bearing press. These tools are designed to safely and easily remove the bearings from your skateboard without damaging them.
  • Wear gloves: Skateboard bearings can be very small and can easily roll away or get lost. Wear gloves to keep a firm grip on the bearings and to protect your hands from any sharp edges.
  • Be careful not to damage the bearing: When removing the bearings, be careful not to damage the bearing races or the balls inside. This can cause the bearing to malfunction or fail.
  • Clean the bearings: Before reinstalling the bearings, make sure to clean them thoroughly. Use a degreaser or a cleaning solution to remove any dirt or grime that may have accumulated on the bearings.
  • Lubricate the bearings: After cleaning the bearings, apply a small amount of lubricant to the balls and races. This will help the bearings to spin smoothly and reduce friction.
  • Keep the bearings organized: Once the bearings are removed, keep them organized and in a safe place. This will make it easier to reinstall them and will prevent any from getting lost.

 

Conclusion

In conclusion, removing skateboard bearings can be done in a few simple steps. First, use a bearing tool or a flathead screwdriver to remove the speed ring or bearing spacers. Next, use a bearing press or a pair of pliers to remove the bearings from the wheel. Be sure to clean and lubricate your bearings before reassembling your skateboard. With proper care and maintenance, your bearings will last longer and provide a smoother ride.

Josh Mitchell

Josh Mitchell

"I live and breath boardriding"

Recent Posts

How To Make A Wakeboard Rails
How To Make Wakeboard Rails

Wakeboarding has emerged as one of the most exhilarating water sports, combining elements of surfing, snowboarding, and skateboarding into a thrilling experience. As wakeboarders push

Read More »
How To Do A Scarecrow Wakeboard
Safety In Wakeboarding

Wakeboarding is an exhilarating watersport that combines elements of water skiing, snowboarding, and surfing. As with any adventure sport, safety should be a top priority

Read More »